Dimensional Measurands / Length

Our service in the calibration laboratory for Dimensional Measurands

Based on our long-time experiences we offer accredited calibration services for dimensional measurands according to ISO/IEC 17025 with DAkkS calibration certificate.

For the calibration of your dimensional measuring equipment, our calibration laboratory has a large number of modern, high-quality reference and working standards.

Our range of services includes the DAkkS calibration of:

Length Measuring Equipment with adequate measuring uncertainties, e.g.:

  • outside micrometers and vernier calipers up to 1000 mm
  • setting standards for outside micrometers from 25 mm to 1000 mm
  • dial indicators up to 100 mm, dial comparators up to 3 mm and dial test indicators up to 1.6 mm
  • outside calipers from 0 mm to 500 mm, inside calipers from 4 mm to 150 mm
  • inside micrometers up to 1000 mm and bore gauges with 2-Point contact from 4 mm to 100 mm
  • 3-Point internal micrometers from 4 mm to 100 mm
  • snap gauges from 20 mm to 250 mm as well as indicating snap gauges and passameters from 0 mm to 500 mm
  • 90° steel squares and protractors from 0° to 360°, side length up to 300 mm
  • knife edge straight edge up to 300 mm

Gauges with smallest measuring uncertainties, e.g.: 

cylindrical setting gauges

  • setting rings, diameter from 2 mm to 280 mm
    optional roundness deviation and/or straightness and parallel deviation
  • limit plug gauges, diameter from 1 mm to 350 mm
    optional roundness deviation and/or straightness and parallel deviation
  • test pins, diameter from 1 mm to 20 mm

thread gauges (single-start and multi-start cylindrical inside and outside threats with straight and symmetrical flanks)

  • outside threads, simple pitch diameter – nominal diameter from 1 mm to
    350 mm, nominal lead from 0.25 mm to 6.0 mm
  • inside threads, simple pitch diameter – nominal diameter from
    2.2 mm to 200 mm, nominal lead from 0.45 mm to 6.0 mm

On-site calibration in the department of dimensional measurands

Your measuring equipment is permanently in use and the delivery to a calibration laboratory is not possible due to technical or temporal reasons?

Our experienced on-site team comes directly to your place. In this way, you save yourself unnecessarily long downtimes and have a competent contact person directly on site.

We also calibrate the following length measuring devices on-site in our mobile measurement lab, depending on the technical requirements, according to accredited calibration procedures (DAkkS).

  • outside micrometers and calipers up
    to 500 mm
  • dial indicators up to 100 mm, dial comparators up to 3mm and
    dial test indicators up to 1.6 mm
  • outside calipers from 0 mm to 500 mm,
    inside calipers from 4 mm to 150 mm
  • 3-Point internal micrometers from 4 mm to 100 mm
  • snap gauges from 20 mm to 250 mm as well as indicating snap gauges and passameters
    from 0 mm to 500 mm

Our complete range of calibration services, including expanded measuring uncertainties, can be found in the Annex to accreditation certificate (D-K-15186-01-01).

 

Furthermore we offer a calibration with certificate e.g.:

  • spring-tape measures up to 50 m
  • steel rulers
  • flat straight edges up to 2500 mm
  • shaft spirit levels and precision levels
  • inclinometers
  • gauge blocks > 100 mm to 1000 mm
  • radius gauges
  • feeler gauges
  • height gauges and marking-out systems
Dimensional Measurands / Length / Bild-1
Dimensional Measurands / Length / Bild-2
Dimensional Measurands / Length / Bild-3
Dimensional Measurands / Length / Bild-4